Industry News

Industry news: standards interpretation, selection guides and application notes for dampers, casters, gas springs, conduits, hinges and chains.

All Industry News
Caster bracket types compared: plate, stem, grip and expanding adapters
Caster bracket types compared: plate, stem, grip and expanding adapters
2026-11-01 · Industry News The bracket decides how a caster mounts and carries load. Four common bracket types compared by mounting condition and equipment, with a quick rule for choosing by structure.
Damper absorbed energy vs cycle rate: how to avoid thermal failure
Damper absorbed energy vs cycle rate: how to avoid thermal failure
2026-10-31 · Industry News Damper temperature rise comes from absorbed energy per cycle times cycle rate. A three-step check for continuous duty: energy per stroke, heat power, allowed temperature rise - and when to size up.
Balancing thermal pad thickness vs hardness
Balancing thermal pad thickness vs hardness
2026-10-30 · Industry News Thickness sets the thermal-resistance floor; hardness decides real contact area. How both interact with mounting pressure, plus common combos for 1-5W devices.
Five signs your eBike chain is worn out
Five signs your eBike chain is worn out
2026-10-30 · Industry News Mid-drive motors wear chains 2-3x faster than传统 bikes. Five wear signals and the 0.75% replacement threshold, plus why wide-inner-plate chains last longer under high torque.
Stepper or servo for IVD pipetting axes?
Stepper or servo for IVD pipetting axes?
2026-10-30 · Industry News Pipetting axes need low-speed smoothness and repeatable positioning, not raw power. Compare stepper and integrated servo on low-speed torque, encoder resolution and volume, with per-axis recommendations.
RV reducer sizing: backlash and torsional stiffness are the hard specs
RV reducer sizing: backlash and torsional stiffness are the hard specs
2026-10-30 · Industry News Positioning accuracy of a robot joint lives or dies on the stiffness chain; backlash and torsional stiffness are the two hardest links to compensate. Definitions, test methods and typical ZKRV values.
Torque hinges on equipment service doors: where they pay off
Torque hinges on equipment service doors: where they pay off
2026-10-30 · Industry News Exposed hinges, swinging doors and aging gas struts are the three pains of service doors. Torque hinges integrate axis, friction and holding in one part; sizing notes using the LAMP HG-SFTH series.
IP68 vs IP67 in practice: choosing sealing for conduit systems
IP68 vs IP67 in practice: choosing sealing for conduit systems
2026-10-30 · Industry News IP67 is short-term immersion; IP68 means continuous immersion with conditions declared by the maker. In conduit systems the conduit is rarely the weak point - fittings are. Selection advice included.
Why double-wall conduits are preferred for medical equipment cable protection
Why double-wall conduits are preferred for medical equipment cable protection
2026-10-30 · Industry News Medical equipment adds three demands: easy cleaning, flame retardancy and collapse-free bending. The smooth outer layer and fibre reinforcement of double-wall conduits map exactly to these; parameter tables included.
Gas spring mounting direction affects service life: three common mistakes
Gas spring mounting direction affects service life: three common mistakes
2026-10-30 · Industry News Rod-down is the first rule of gas spring mounting. Three frequent mistakes - rod-up, side loads from poor pivot geometry, zero-stroke margin - and how HAHN gas springs should be sized and checked.
Caster tread materials for cleanrooms: a practical comparison
Caster tread materials for cleanrooms: a practical comparison
2026-10-30 · Industry News Dust generation vs load capacity is the core trade-off for cleanroom casters. Compare PU, conductive rubber and nylon treads on particle emission, chemical resistance and noise, with recommendations for three scenarios.
Why adjustable dampers are recommended for robot end-of-arm impact
Why adjustable dampers are recommended for robot end-of-arm impact
2026-10-30 · Industry News Impact energy at the robot wrist changes with payload and speed. This note explains the two-chamber design of adjustable dampers and a three-step sizing method by absorbed energy and cycle rate.
Contact Us Contact Us
Copyright © 2026 Ling Pei Jian (Shanghai)Ltd All rights reserved. [沪ICP备19004032号-1]
Back to top